Cisco 2600 Series Password Reset

0
121

Lab Prerequisites:

  • A Cisco 2600 Series router or greater that has an unknown console or enable password.
  • An active Serial Console session to the device that you’re unable to log into.

 

Lab Objectives:

  • Break the boot sequence when powering on the Cisco 2600 Series router to place yourself in ROM monitor mode.
  • Change the configuration register to 0x2142 to make the router bypass the contents of NVRAM when booting then reset the router.
  • (Option 1) – Once booted, place yourself into privileged mode and copy the start up-config to the running config. Afterward, you may change the line password or enable password and write the configuration by to NVRAM by issuing the copy run start command.
  • (Option 2) – Once booted, place yourself into privileged mode and do a write erase to clear the contents of the NVRAM.
  • Now change the configuration register back to 0x2102 to boot set the router to boot normally and load the NVRAM contents upon boot.
  • Now change the configuration register back to 0x2102 to boot set the router to boot normally and load the NVRAM contents upon boot.

Lab Instruction:

As shown below is a Cisco 2651XM router that has a console password on the device. With such a password you cannot access exec mode without authenticating this password correctly. When buying routers used, you may commonly be faced with scenario.

 

Router con0 is now available

Press RETURN to get started.

User Access Verification

Password:

 

Step 1. Power cycle the router or power on the router initially. While the router is booting you’ll need to break the boot sequence to boot the router into bootrom, you do this by holding down CTRL and pressing PAUSE BREAK. Do this repeatedly till you are placed at the bootrom prompt.

 

System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)

Copyright (c) 2003 by cisco Systems, Inc.

C2600 platform with 262144 Kbytes of main memory

monitor: command “boot” aborted due to user interrupt

rommon 1 >

 

Step 2. Change the configuration register so that the router will ignore the contents of the NVRAM when booting into Cisco IOS. Set the configuration register to 0x2142 and boot the router.

 

rommon 1 >confreg 0x2142

rommon 2 >reset

 

Step 3a. (Option 1 – Reset Password) – After the router has booted into Cisco IOS, you’ll be prompted by the initial configuration dialog, type n here and press enter and you’ll be placed into user mode. Now you’re able to place your self into privileged mode by typing enable. Once in privileged mode you can copy the start-up configuration to the running configuration and then change the passwords manually then saved the configuration by to NVRAM by typing copy run start.

 

         — System Configuration Dialog —

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

Router>enable

Router#copy start run

Destination filename [running-config]?

506 bytes copied in 3.868 secs (168 bytes/sec)

HocCisco#configure terminal

HocCisco(config)#enable secret NEWENABLEPASSWORD

HocCisco(config)#line con 0

HocCisco(config-if)#password NEWPASSWORD

HocCisco(config-if)#end

HocCisco#copy run start

Destination filename [startup-config]?

Building configuration…

[OK]

HocCisco#

 

Step 3b. (Option 2 – Factory Reset) – After the router has booted into Cisco IOS, you’ll be prompted by the initial configuration dialog, type n here and press enter and you’ll be placed into user mode. Now you’re able to place your self into privileged mode by typing enable. Once in privileged mode you can erase the contents of NVRAM by issuing the write erase command.

By issuing the write erase command it will erase the startup configuration which is stored in NVRAM and reset the router back to the factory default. This will remove ALL configuration from the router. If you just want erase the configuration on a Cisco Router or Switch, using the write erase command followed by reload will complete the task.

 

         — System Configuration Dialog —

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

Router>enable

Router#write erase

Erasing the nvram filesystem will remove all files! Continue? [confirm]

[OK]

Erase of nvram: complete

Router#

 

Step 4. Once you’ve performed a password reset or NVRAM sanitation, you’ll need to set the configuration register back to 0x2102 so the router will boot normally and load the NVRAM contents upon a reboot or power failure.

 

Router#configure terminal

Router(config)#config-register 0x2102

Router(config)#end

 

LEAVE A REPLY

Please enter your comment!
Please enter your name here

This site uses Akismet to reduce spam. Learn how your comment data is processed.